• Three (3) section, telescoping steel constructed of high strength steel, certified to 70,000 psi
• Bolt-on egress with full 1500 lb. rating
• Electronically controlled, multiplexed and microprocessor based system.

Ladder Assembly
• Ladder sections are trussed vertically and diagonally with round steel tubing
• Environmentally sealed ladder sections to protect against corrosion
• Aerial device is 3rd party tested by Underwriters Laboratories, Type 1 tested
• All ladder rungs are round and welded to each section in two places with k-bracing for rigidity
• Ladder sections are designed with adequate hand spacing and room for vertically mounted cable tracking, resulting in unobstructed egress on ladder
• Each rung is covered with a secure aggressive composite photo-luminescent rung cover. Extension and retraction motion by a dual hydraulic powered cylinders and cable pulley system.
• Rotation motion through a 54.00" swing bearing/spur gear, driven by two planetary hydraulic motors.
• Elevation motion through double acting, lift cylinders (5 deg below horizontal to 75 deg above)
• All cylinders designed with integral holding valve cartridges in the event of a hydraulic line failure
• Rotational brake applies when pressure control is released.

Turntable Deck
• 96.00" wide x 81.00" long turntable is constructed of a 1.00" thick deck, coated with a non-skid, chemical-resistant material
• Pull-out, drop-down steps provide access to the turntable from rear body, one each side of the truck
• Stairs are lit by lights activated by the aerial master switch
• Includes control console and space for hydraulic and electrical components

Aerial Device Power
• One turntable control station located on driver side
• Additional aerial controls available at aerial tip and pump panel
• Aerial controls are electronic over hydraulic, fully multiplexed and proportionate
• All aerial device controls have fail-safe manual hydraulic overrides.
• Hydraulic load sensing piston pump, capable of multiple-function operation without speed loss.
• High pressure hydraulic manifold block, with test ports
• Pressure and relief filtration system
• Hydraulic reservoir of 65 gallons
• Relief valve set at 3150 psi to protect hydraulic system components
• 12V emergency power unit (EPU) with 30-minute run time, capable of stowing the ladder in the event of a power loss
• High idle is controlled by the microprocessor to automatically adjust engine rpm to load condition
• Three-speed aerial control switch

Control Stations
• Wireless, pendent control box, at driver’s side improves visibility
• Turntable control station
• Wireless remote control aerial operation (optional)

Aerial Waterway
• Water swivel 5.00 inch capable of 360 degree rotation
• Telescoping anodized aluminum waterway capable of 1500 gpm
• 5.00" dia. base waterway pipe
• 5.00" swivel capable of operating between -5 degrees and up to 75 degrees
• A 250 psi pressure relief valve located below the torque box
• Aerial monitor (electric), capable of 1500 gpm, Akron self-stowing monitor (standard)
• Water flow monitored by the aerial microprocessor
• 5.00" rear inlet to the aerial waterway

Electrical System
• Electrical swivel capable of 360 degrees with 36 collector rings, each capable of 20 amps
• 110V electrical system, two 20 amp NEMA L5-20, 3-prong water proof receptacles (optional) at tip of ladder
• Four (4) 12V unity lights standard, two at tip, two at base

Pump and Pumphouse
• A midship pumphouse, centered in the frame, ahead of body
• Valves-Akron standard (Elkhart optional)
• Pump pressure governor standard (option for a discharge relief valve or TPM)
• Removable pump panels provide access to the pump for maintenance

Aerial Body
• Compartmentation fabricated from .125" 5052 aluminum with a tensile strength of 38,000 psi
• Side compartments integral assembly with the rear fender
• Neoprene elastomer isolators will isolate chassis movement from the body structure
• Bodies are formed and welded construction for durable, long lasting design without the unnecessary weight.
• Exclusive Pierce underslung steel body supports featuring 3-point isolated mount system. This reduces torsional stress and road shock from being transmitted into the body. The underslung design prevents compartment floors from sagging after years of use.
• Aluminum extruded rub rails, bolted on for easy repair
• Galvaneal steel, stainless steel, high-strength aluminum
• Interior of all compartments are painted with multispec to hide dirt, abrasions, and protect from oil, gas, and hydraulic spills.
• Automotive-style hinged doors constructed with double pan, double seals, enclosed latches, and .25" hinge pins.
• Roll-up doors w/lifetime warranty (available in satin or painted finish) .
• Handrails are Pierce's exclusive "cross knurled" design to reduce hand slippage.